Halloween Mist maker
Description
Halloween figures or maybe Santa clause and his deer's could be put on this mist maker. Other figures that will fit: A sun and planet system - but then the arms need to be extended. I dimension the pipes on left and right for standard size of Halloween Pumpkins so if you need to modify/replace the figures you only need a whole that matches that. The middle figure is resized 300% so the whole is 300% of its original size. **Updates:** |Date|Part|Description| |------|------------|--------------- | |2018-11-04|box.lid.2|Alter the height and outer ø on box.lid small pipe holders to fit correctly| ** Videos ** Testing the mist: https://www.youtube.com/watch?v=F2CmjX3pRBk Sprint 1 done: https://www.youtube.com/watch?v=J53mOXs0KdA **Required parts** A lot of print time: only the 300% enlarged [Pumkin 3 ](https://www.thingiverse.com/download:1697750) took 60h to print | Amount | Unit | Description | | ---------- | ----------------| | 1 | piece | [Mist maker](https://www.aliexpress.com/item/Ultrasonic-Mist-Maker-Nebulizer-Atomizer-Head-without-Lights-for-Humidifier/32693755828.html) | | 1 | meter | [PVC Tube tubes (Inner ø: 8mm Outer ø: 11mm)](https://www.bauhaus.se/pvc-slang-8x1-5mm.html) | 4 | piece | Rubber seal (Inner ø: 10mm Outer ø: 14,4mm, 1,8 mm thick) used on top of lid | | 4 | piece | Single loop self-locking strap to secure pvc tube under box lid | | 1 | bottle | Varnish, used to plug water leaks on box and to impregnate floater | | 1 | piece | [1515 fan blower](https://www.aliexpress.com/item/3D-Printer-Fan-5015-12V-24V-0-23A-Sleeve-Bearing-Brushless-Fan-Centrifugal-For-Reprap-i3/32890197384.html) | | 2 | piece | Screw to fasten the fan on the box-lid | | ≈ 500 | gram | Filament for box (no support, raft, 100% infill) | | ≈ 200 | gram | Filament for box-lib (no support, raft and 100% infill ) | | ≈ 45 | gram | Filament for floater ( no support, 2% infill rectangle) | | ≈ 2 x 65 | gram | Filament for side pipes ( no support, 100% infill rectangle) | | ≈ 24 | gram | Filament for main pipe ( no support, 100% infill rectangle) | | ≈ 600 | gram | Filament for enlarged pumpkin 3 ( support from build plate, 9% infill rectangle)| | ≈ 50 | gram | Filament for pumpkin 3 ( support from build plate, 9% infill rectangle, raft)| | ≈ 60 | gram | Filament for pumpkin 2 ( support from build plate, 9% infill rectangle, raft)| | 1 | piece | 12V DC Power supply to fan | | 1 | piece | 24V DC Power supply to Mistmaker | | 1 | piece | 300 % Enlarged [Pumkin 3 ](https://www.thingiverse.com/download:1697750)| | 1 | piece | Normal size [Pumkin 3 ](https://www.thingiverse.com/download:1697750)| | 1 | piece | Normal size [Pumkin 2 ](https://www.thingiverse.com/download:1697748)| | 1 |piece | [plumbing tape (12 m)](https://www.geko.net/en/adhesive-tapes/various-tapes/teflon/), make box and fittings air tight | The "floater" is used to make mist make float in the water bath (box) and can be used in a pool or pond. **Optional parts** | Amount | Description | | ---------- | ----------------| | 1 piece | Sonoff Basic | | 4 pieces | [SG 90 9g Mini Servo](https://www.aliexpress.com/item/SG-90-9g-Mini-Micro-Servo-For-RC-Helicopter-Airplanes-Model-Airplane-Accessories-Mini-Steering-Gear/32845387964.html) | | 4 pieces | [DIY 10mm servo valve](https://www.thingiverse.com/thing:1624066) | | 1 piece | 5v power supply for SG 90 Servos | | 10 piece | 2812b Led strip IP65, 6 pieces in main figure 2 pieces in left and right figure | I have added a schematic how to connect the things up. I would use [Tasmato](https://github.com/arendst/Sonoff-Tasmota) firmware for controling servos. **This is an ongoing project so my intention is:** * wire everything up so i can remote control it. * coat with putty * sand * airbrush * clear coat with varnish
Statistics
Likes
12
Downloads
0