Prusa Bear-BMG fusion (indirect filament sensor) for MK3 / MK2.5
Description
This Bear BMG extruder is a fusion of excellent extruder made by Pekcitron (Bear Extruder) and the bondtech BMG 3:1 . I tried to integrate the indirect filament sensor with a magnet (based on this design: https://www.thingiverse.com/thing:3241561 RaavHimself--> very smart design! ). To use the indirect filament sensor you need a MR105z bearing (5x10x4) and a round neodymium 8x3 No need to change nothing in the firmware! Need also n°1 thread insert (used to fix the extruder bottom to the X_carriage on left up side) Many thanks to all people who tried develop a better extruder, specially Pekcitron RaavHimself and Lee0101. A big thanks also to Eric Clinedinst who helped me to find the first issue. This is the BOM list for the internal part: 1x 5x10x4 (MR105z) Bearing for indirect filament sensor 1x round neodymium 8x3 https://www.amazon.it/dp/B075FKTCZG/ref=cm_sw_r_cp_apip_pkFCQPIVjH3OA 2x 5X8X2.5 Bearing https://www.bondtech.se/en/product/ballbearing-5x8x2-5 1x Shaft Assembly https://www.bondtech.se/en/product/shaft-assembly 1x Motor Gear https://www.bondtech.se/en/product/motor-gear/ 1x 3X32 mm Shaft https://www.bondtech.se/en/product/shafts/ 1x Thread insert https://www.bondtech.se/en/product/thread-inserts/ 1x Thumbscrew Assembly https://www.bondtech.se/en/product-category/spare-parts/thumbscrew-assembly/ 1x Push-Fit Connector (or you can model in fusion to adapt PC4-....) https://www.bondtech.se/en/product/push-fit-connector/ 1x 1.75 / 5.0 Bontech Drivergear kit. (No need if you own a MK3) 1x pancake motor with at least 16N.cm https://zaribo.com/stepper-motors/126-zaribo-pancake-motor-by-ldo.html 3x M3x50 screw to connect the pancake motor untill the X-carriage. For some instruction assembly you can refer to the Bear X-axis project: https://github.com/gregsaun/bear_extruder_and_x_axis/tree/master/manual/quick_assembly **** 03/12/18 UPDATE 1: Update design with different position of the filament sensor, now no need to modify the firmware. Just update the extruder_bottom and X_carriage mk3, sensor lid and magnet cover. **** 06/12/18 UPDATE 2: Increased the hole path filament (but remember always use a 2mm drill bit to clean and smooth the path), refinement on the ball bearing room space, and for the X_carriage i corrected the space for molex connector. **** 07/12/18 UPDATE 3: new modification of the bottom extruder to easily insert the e3dv6 with collet clip. Not yet printed so test it at your risk!. I have a new idea to better insert the extruder, i will keep informed once it work well. **** 07/12/18 late night UPDATE 4: totally redesigned how to insert e3dv6, now very easy to put-in and take out with collet clip and bowden tube. Little bit refinement on bearing room. **** 08/12/18 UPDATE 5: As feedback from Panayiotis_3d i modified how to fix the 3 part (X carriage, extruder bottom and extruder top), unfortunately you have to use n°3 M3x50 and n°1 M3x30. **** 09/12/18 UPDATE 6: thanks to KappaMi and Panayiotis_3d for their suggestions. I moved the e3dv6 a liitle bit more down, i increased a little bit more the filament path, decreased the diameter for the filament sensor screw hole and much more.... **** 11/12/18 UPDATE 7: New way to keep the bearing with stable pressure on filament, update bearing slide holder and extruder bottom. **** 13/12/18 UPDATE 8: New Alpha 6 design. as suggested i add a hole for square nut to fix the lever instead the thread insert and add a hex nut fo fix the fan support (instead the thread insert). i also add a square nut to keep better in place the screw for the bearing pressure. See the top of the extruder bottom to see this change (my english is not good as i would like to describe these changes...sorry). Anyway from update 7 all are stable and usable. Hope to hear some feedback about new changes. **** 26/12/18 UPDATE 9: Nothing changed here but now it out of Alpha. It is stable, i have 2 extruders mounted and they work extremely well from 2 weeks. **** 31/12/18 UPDATE 10: Added stl file of MK2.5 X-carriage. Re-upload step files for MK3 **** 03/01/19 UPDATE 11: Added stl file of Extruder top without the "Venturi hole" **** 05/01/19 UPDATE 12: Added a .pdf file of quick assembly photos **** 10/01/19 UPDATE 13: Added .stl files of cable guide back part a. and part b. Thanks to Gabe Condrea for your precious and continually suggestions and for tipped me!!! **** 16/01/19 UPDATE 14: Updated the assembly guide (thanks to repvik) **** 21/01/19 UPDATE 15: i added a version of Extruder bottom with a PC4-M6 and a Lever with a 2mm recession to solve the issue with short screw if you are usion the original Thumbscrew Assembly.
Statistics
Likes
126
Downloads
0