Pickle Canopies for Toothpick style micro fpv quad (14x14 and 19x19)
Description
If you like my work please consider following/subscribing to my feeds : [Instagram](https://www.instagram.com/ledrone.club/) and [YouTube](https://www.youtube.com/c/ledroneclub) Or you can [support me via ko-fi](https://ko-fi.com/ledroneclub) ----- **There's a new version of this pod for 14x14 cams, the [PicklePod2](https://www.thingiverse.com/thing:3944156). It's a bit bigger and heavier but you may like it as well especially if you're building a 3 inch setup** If you're looking for a frame option for this canopy check my [PicklePick 65mm and 3 inch frames](https://www.thingiverse.com/thing:3857976). ### Buy one ? Some of those canopy variants are distributed here : * [RotorVillage (CA)](https://www.rotorvillage.ca/TPU-Whoop-Canopy-p/3d-whoop-canopy.htm) * [Taco-RC (HK), some versions in frame kits](http://taco-rc.com/fpv-racing/frame/ledroneclub/) The Pickle canopy is made for Toothpick style micro quadcopters and comes in different variants. Starting from a very basic & light one to a full featured with all sorts of antenna mounts (crossfire, 2.4Ghz, vtx). The canopy is compatible with most of (all) nano 14x14mm cameras with screw mounts, eg : Caddx EOS2, Runcam Nano 2, Runcam Nano Racer, Foxeer Predator nano, etc. To use it simply stick it on the top of the screws holding the 26 mm x 26 mm FC board(s). Yes, it even fits the Diatone GTB/Cube micros :) NOTE : there's also a 19x19 version for bigger micro cameras. Here are the different versions : * Basic : 1.7g with just holes on the side to attach antennas with a small ziptie * CRSF : Small ears with holes to pass a crossfire trimmed antenna (called also a Faebu Mount ;) ) * 24G : 2 side tubes to pass 2.4GHz antennas and use small RC tubes to hold them up. * *_VTX : crossfire or 2.4G + vtx mount * Full : have all the mounting options (antennas, vtx). This one weights ~2.7g. ### Currently supported cameras (14x14 format) * [Runcam Nano 2](https://www.banggood.com/RunCam-Nano-2-13-700TVL-1_8mm2_1mm-FOV-155170-Degree-CMOS-FPV-Camera-for-FPV-RC-Drone-p-1469656.html?p=SI190238022477201908) (14mm x 14mm size). * [RunCam Racer Nano](https://www.banggood.com/Runcam-Racer-Nano-CMOS-700TVL-1_8mm2_1mm-Super-WDR-Smallest-FPV-Camera-6ms-Low-Latency-Gesture-Control- Integrated-OSD-for-FPV-Racer-Drone-p-1468281.html?p=SI190238022477201908) (14mm x 14mm size). * [Foxeer Predator V4 Nano](https://www.banggood.com/Foxeer-Predator-4-Nano-Super-WDR-4ms-Low-Latency-1000TVL-FPV-Racing-Camera-OSD-43-169-NTSC-PAL-for-RC-Drone-p-1529597.html?p=SI190238022477201908) (14mm x 14mm) * [Caddx EOS2](https://www.banggood.com/Caddx-Turbo-EOS2-43-1200TVL-2-1mm-13- CMOS-Mini-FPV-Camera-NTSCPAL-For-RC-Drone-p-1309237.html?p=SI190238022477201908) (14mm x 14mm size). * Micro cameras (19mm x 19mm size, like Runcam Sparrow/Robin, Foxeer Falkor micro, etc.) ### Changelog * 10 aug. 2019 : Canopies are upgraded with a better fitting camera mount (it's thicker) and holes on the rear side to attach antennas with a ziptie. * 24 apr. 2019 : added a 19x19 version with crossfire mount (ears) * 19 apr. 2019 : bumped 14x14 version to 1.3 and basic version to 1.4. Fits better the EOS2 camera, is less tall overall (could go further). Solved a width problem as well, canopy could touch the props if your print is crappy or on an impact i guess. * 18 apr. 2019 : added a 19x19 version for micro size FPV cameras. ### Printing tips Print using TPU filament (Eg : Sainsmart 95A TPU) and use supports.
Statistics
Likes
279
Downloads
0