Ghettostation Antenna Tracker Case
Description
My Case Design For The Excellent Ghettostation Antenna Tracker From Kipk. The Case Was Inspired By The Ez Antenna Tracker / Ground Station, Eztracker Immersion Rc By Rchobbysuk Here On Thingiverse. The Case Features: ------------------------ - 0-135 Degree Tilt Head - 360 Degree Pan Mount (Ball Bearing Supported) - Antenna Quick Change/Release To Allow Use Of Multiple Different Antennas - Immersionrc Duo 5800 V3, V4, Uno5800 V2 And Uno2400 Video Rx Mount (Single Mini Din Connection, Lever For Frequency Selection) - Lawmate 2.4Ghz Mount - 3Dr Radio Telemetry Module (900Mhz Or 433 Mhz) Mount On The Tracking Plate - Easy Access Battery Compartment For Up To 3700Mah 4S Lipo Pack - Lcd Mount And Holes For The 3 Selection Buttons - Arduino Mega 2560 Rev 3 Mounting Tabs Including Usb Connector Cut Out - Mounts For Battery Voltage Alarm, Power On/Off, Ground Osd Power On/Off, 4X Video Out, 1X T-Style/Deans Power Connector - Tripod Quickmount And Additional Feet For Table Top/Car Roof Top Positioning Please Refer To The Instructions For Details On The Used Components And Links To The Software And Forum. Updates: 21/11/2014: - Updated Rear Case With More Servo Clearance To Accommodate Taller Servos Such As The Gws S125-1T/2Bb Winch Servo And Nut Slots Added For Reach Cover Mount (The Plastic Wears Out Quite Quickly If The Case Is Opened And Closed Multiple Times. Adding A Nut Solves This). - Servo Spacer For Gws S125 Added 31/12/2014: - Immersionrc Duo5800 Mount Renamed To Duo5800_V3 In Preparation For Release Of A Mount Suitable For The Duo5800 V4 4/1/2014: - Happy 2015 Everyone. Mounting Plate For Duo5800 V4 Added. You Will Need To Print 2 Of The Duo5800_Push.Stl And Duo5800_Lever.Stl For The V4 Of The Duo5800 As It Has Both Band And Frequency Selection Buttons. As I'M Not The Proud Owner Of A V4 And The Design Is Based On Drawings Received From Immersionrc, Please Do Let Me Know In Case Changes Are Required Once You Tested It Out (And Also Drop A Note In Case It Works Fine As Is). Thanks 27/1/2015: Turnplate Updated To Allow Removal Of The Top Without The Need To Pull The Cables Through Before. 29/1/2015: Added Rx Mounts For Immersionrc Uno5800 V2 And Uno2400 (Same Mount As Uno5800) Receiver And Lawmate 2.4Ghz Receiver 16/2/2015: After Receiving Feedback That A Large Part Of The Files Failed To Print In Slic3R And Cura, I Believe I Found An Error In The Scaling Method I Used To Export The Files. All Files Are Updated And Check Out In 3 Slicers I Have Tested So Far. Please Report Back In Case There Are Still Issues. Other Changes: - Added Spacers For The Bearings As, Depending On Servo And Filament Used There Is A Gap Between Bearing And Turnplate. Print The Required Thickness And Insert It Between The Bearing Mount And The Rear Top Cover - Updated The Rear Case To Allow The Use Of A M4 Nut For The Battery Door As The Plastic Wears Out After Some Time. - 2 Versions Of The Rear Case Are Not Available. 1 Version Comes With 4 Video Connectors And 1 Deans Connector, The Other With 2 Video Connectors, One Deans And One Xt60 Connector. 01/03/2015: - Added Mirror Version Of The Uno5800 Mount In Case You Want To Install It On The Left Side Or Have One Uno5800 On One And A Uno2400 On The Other Side. 29/03/2015: - Corrected Uno2400 Mount Added (Left And Right Side) 11/04/2015: - Added Modular Antenna Mounts. Allows Quick Change Of The Following Antenna Types: 1) Immersionrc 5.8 Patch (Imrc5.8_Lock.Stl) 2) Immersionrc 2.4 Patch (Imrc2.4_Lock.Stl) 3) Circular Wireless 5.8 Helix (Cw5.8_Lock.Stl) You Will Need To Replace The Tilt Head Plate With The New Lock Plate (Head_Lock.Stl).
Statistics
Likes
420
Downloads
0