Purge Bucket that fits the A20T Geeetech Printer

Description

I took two of the things I liked about two different tools and put them together to make the ultimate one-stop-shop purge bucket. Dont forget your X-axis cover plate! Enjoy. Printed by .28,190/50c @ 40 printer speed on an Ender 3 I chose not to use supports but it held up perfectly, I was impressed. G28 ;Home M104 S{material_print_temperature} ;M104 S200 ; Set Extruder temperature for new tool M109 R195 ; Wait for Extruder temperature M211 S0 ; Turn off soft stops (to get to the bucket) G1 X-9.5 F9000 ; Go to X=-9.5 at 150 mm/sec (go to the bucket) G92 E0 ; Set current extruder position to 0 M109 {material_print_temperature} ;M109 R195 ; Wait for Extruder temperature, heat OR cool (in case of change) M211 S1 ; Turn on soft stops once more G1 F200 E3 ;Start of prime line script M109 R195 ; Wait for Extruder temperature M211 S0 ; Turn off soft stops (to get to the bucket) G0 X-9.5 F9000 ; Go to X=-9.5 at 150 mm/sec (go to the bucket) G92 E1 G1 Z.1 F3000 ; move z up little to prevent scratching of surface G1 X15 Y20 Z1.0 ; Move to location above start-line position G1 X15 Y20 Z0.3 F5000.0 ; move to start-line position G0 E5 F5100 ; Prime nozzle G1 X4.6 Y150.0 Z0.3 F1500.0 E15 ; draw 1st line G1 X15 Y150.0 Z0.3 F5000.0 ; move to side a little G1 X15 Y20 Z0.3 F1500.0 E30 ; draw 2nd line G1 X15 Y20 Z0.2 F3000 ; get ready to prime G4 S1 G0 X-9.5 F6000 ; Wipe G0 X.1 F6000 ; Wipe G0 X-9.5 F6000 ; Wipe ; Final wipes G0 X.1 F6000 ; Wipe G0 X-9.5 F6000 ; Wipe G0 X.1 F6000 ; Wipe G0 X-9.5 F2000 ; Return M211 S1 ; Turn on soft stops once more ; Start Extruder Script End ; Endcode G91 G1 F1800 E-2 G1 Z2000 Z50 G90 G1 X120 Y250 F1500 M104 S0 M106 S0 M140 S0 M84 .x3: ; Start Extruder (Name) 0 M211 S0 ; Turn off soft stops (to get to the bucket) G0 X-9.5 F9000 ; Go to X=-9 at 150 mm/sec (go to the bucket) M104 S{material_print_temperature} ;M104 S200 ; Set Extruder temperature for new tool G92 E0 ; Set current extruder position to 0 Reset extrusion distance on new tool M109 {material_print_temperature} ;M109 R195 ; Wait for Extruder temperature, heat OR cool (in case of change) ; Extrude filament G91 ; Switch the relative positioning M109 {material_print_temperature} ;M109 R200 G1 E130 F90 ;from180 to 200 to reduce curl G1 E1 F90 ; Low speed purge for 1mm (reduce pressure) G92 E0 ; Set current extruder position to 0 G1 E1 F600 ; Retract a bit G90 Switch back to absolute positioning (Cura's default) G92 E0 ; Set the current extrude position to 0, in preparation for the unretract that Cura does (to absolute position E) by default after this) G4 S1 G0 X.1 F6000 ; Wipe G0 X-9.5 F6000 ; Wipe ;Start Final wipes G0 X.1 F6000 ; Wipe G0 X-9.5 F6000 ; Wipe G0 X.1 F6000 ; Wipe G0 X-9.5 F6000 ; Wipe ;G0 X-9.5 F6000 ; Wipe ;G0 X.1 F2000 ; Return M211 S1 ; Turn on soft stops once more ; Start Extruder Script End ; End Extruder 0 G92 E0 ; Reset extrusion distance G1 E0 F500 ; Retract G91 ; With from absolute positioning to relative G0 X.1 F6000 ; Wipe G0 X-9.5 F6000 ; Wipe G1 Z.1 F100 ; lift nozzle by .1mm in relative position G90 ; Return to absolute positioning

Statistics

Category

Tags