ImmersionRC EzTracker Antenna Tracker Case
Description
This Is An Adaptation Of My Ghettostation Antenna Tracker Design To Fit The Immersionrc Eztracker (Currently Version 1). The Case Features: ------------------------ - 0-135 Degree Tilt Head - 360 Degree Pan Mount (Ball Bearing Supported) - Antenna Quick Change/Release To Allow Use Of Multiple Different Antennas - Immersionrc Duo 5800 V3 & V4 As Well As Uno5800 V2 And Uno2400 Video Rx Mount (Single Mini Din Connection, Lever For Frequency Selection) - Lawmate 2.4Ghz Rx Mount - 3Dr Radio Telemetry Module (900Mhz Or 433 Mhz) Mount On The Tracking Plate - Easy Access Battery Compartment For Up To 3700Mah 4S Lipo Pack - Eztracker Lcd Mount With Easy Access To The Selection Buttons And Remaining Module Protected Inside The Case. - Mounts For Power On/Off, 4X Video Out, 1X T-Style/Deans Power Connector - Tripod Quickmount And Additional Feet For Table Top/Car Roof Top Positioning Please Refer To The Instructions For Details On The Used Components In Case You Already Have The Ghettostation Tracker Printed, The Only Items To Be Changed Are: - Case_Front_Ez.Stl - Cover_Front_Ez_V2.Stl - Cover_Front_Ez_Bottom.Stl Please Note: The Mounting Plate For Duo5800 V4 Is Based On Measurements Received From Immersionrc Only. It Has Not Yet Been Tested (I Only Have A V3). Please Post Here In Case You Have Issues With The V4. Do Also Let Us Know In Case It Works Perfectly As Advertised :-). You Will Need To Print 2 Of The Duo5800_Push.Stl And Duo5800_Lever.Stl For The V4 Of The Duo5800 As It Has Both Band And Frequency Selection Buttons. 27/1/2015: - Turnplate Updated To Allow Removal Of The Top Without The Need To Pull The Cables Through Before. 29/1/2015: - Added Rx Mounts For Immersionrc Uno5800 V2 And Uno2400 (Same Mount As Uno5800) Receiver As Well As Lawmate 2.4Ghz Receiver 16/2/2015: After Receiving Feedback That A Large Part Of The Files Failed To Print In Slic3R And Cura, I Believe I Found An Error In The Scaling Method I Used To Export The Files. All Files Are Updated And Check Out In 3 Slicers I Have Tested So Far. Please Report Back In Case There Are Still Issues. Other Changes: - Added Spacers For The Bearings As, Depending On Servo And Filament Used There Is A Gap Between Bearing And Turnplate. Print The Required Thickness And Insert It Between The Bearing Mount And The Rear Top Cover - Updated The Rear Case To Allow The Use Of A M4 Nut For The Battery Door As The Plastic Wears Out After Some Time. - 2 Versions Of The Rear Case Are Not Available. 1 Version Comes With 4 Video Connectors And 1 Deans Connector, The Other With 2 Video Connectors, One Deans And One Xt60 Connector. 01/03/2015: - Added Mirror Version Of The Uno5800 Mount In Case You Want To Install It On The Left Side Or Have One Uno5800 On One And A Uno2400 On The Other Side. 29/03/2015: - Corrected Uno2400 Mount Added (Left And Right Side) 11/04/2015: - Added Modular Antenna Mounts. Allows Quick Change Of The Following Antenna Types: 1) Immersionrc 5.8 Patch (Imrc5.8_Lock.Stl) 2) Immersionrc 2.4 Patch (Imrc2.4_Lock.Stl) 3) Circular Wireless 5.8 Helix (Cw5.8_Lock.Stl) You Will Need To Replace The Tilt Head Plate With The New Lock Plate (Head_Lock.Stl). 30/07/2015: Added A Quick 4 Part Version Of The Case To Print On Smaller Printers. Part 1 Needs To Be Glued To Part 2 And Part 3 Needs To Be Glued To Part 4 Along The Split Line. Please Report Back In Case You Face Issues. - Cutcase_Ez_Part1.Stl - Cutcase_Ez_Part2.Stl - Cutcase_Ez_Part3.Stl - Cutcase_Ez_Part4.Stl
Statistics
Likes
476
Downloads
0