Gravitrax Ball wheel V2 - Kugel-Rad V2
Description
**Gravitrax Ball wheel V2** - Difference in height 80mm - no support necessary - 3 pressure parts: wheel, gear, pillar - Printing time approx. 8 hours - it is required: (motor see links) 1 x M5 screw 50mm or threaded rod 1 x M5 washer 1 x M5 self-locking nut (2x with threaded rod) 1 x motor DC6V N20 Micro Gear 10/15 / 20RPM GA12N20 1: 1000 (shaft Ø3mm x 10mm) 1 x cable for power supply 4.5 to 6 volts (ideally USB) - The motors are available with very different speeds, please pay attention to this when buying. The motor should not have more than 15 revolutions per minute at 6 volts. Note: the gearbox is 12mm long for the motor with 1: 1000 ratio, this motor is the right one. - The motor can be operated with 4.5-6V. - Depending on the printer tolerance, it may be necessary to carefully enlarge or glue the holes in the axes and the motor. #[Video Youtube](https://youtu.be/UbCWFshZv9I) **Where to buy Motor - Bezugsquellen Motor** [Amazon.de](https://www.amazon.de/Weilifang-GFCGFGDRG-15RPM-20rpm-Elektro-Getriebe-Motor/dp/B08FLD5G1R/ref=sr_1_8?__mk_de_DE=%C3%85M%C3%85%C5%BD%C3%95%C3%91&dchild=1&keywords=DC+6V+Getriebemotor+30rpm&qid=1615501273&sr=8-8) [Amazon.de search](https://www.amazon.de/s?k=DC+6V+Getriebemotor+High+Torque+1%3A+1000&__mk_de_DE=%C3%85M%C3%85%C5%BD%C3%95%C3%91&ref=nb_sb_noss) [ebay.de](https://www.ebay.de/itm/1Pcs-DC6V-12V-N20-Micro-Gear-Motor-Gear-Ratio-1-1000-High-Torque-10-15-20-30rpm/172438281294?hash=item28261f5c4e:g:u2cAAOSw2xRYSI8c) [ebay.de](https://www.ebay.de/itm/1x-10RPM-Mini-Getriebemotor-6V-DC-Metallgetriebe-1-1000-Ubersetzungen-Wenig-Larm/363313228161?_trkparms=aid%3D1110006%26algo%3DHOMESPLICE.SIM%26ao%3D1%26asc%3D20201210111314%26meid%3D0f1f989e12fc4b66950d1b4d75fe062e%26pid%3D101195%26rk%3D4%26rkt%3D12%26mehot%3Dco%26sd%3D172438281294%26itm%3D363313228161%26pmt%3D1%26noa%3D0%26pg%3D2047675%26algv%3DSimplAMLv9PairwiseUnbiasedWeb%26brand%3DMarkenlos&_trksid=p2047675.c101195.m1851) [aliexpress.com](https://de.aliexpress.com/item/4000876633626.html?spm=a2g0o.productlist.0.0.6ea015cfMyLUM7&algo_pvid=2c29d8a4-582f-4aab-9bba-da99539e7769&algo_expid=2c29d8a4-582f-4aab-9bba-da99539e7769-9&btsid=) **Gravitrax Kugel-Rad V2** - Höhendifferenz 80mm - kein Support notwendig - 3 Druckteile: Rad, Zahnrad, Pfeiler - Druckzeit ca. 8h - es wird benötigt: (Motor siehe Links) 1 x M5 Schraube 50mm bzw. Gewindestange 1 x M5 Unterlegscheibe 1 x M5 selbstsichernde Mutter, (bei Gewindestange 2x) 1 x Motor DC6V N20 Micro Gear 10/15/20RPM GA12N20 1:1000 (Welle Ø3mm x 10mm) 1 x Kabel zur Stromversorgung 4,5 bis 6 Volt (idealerweise USB) - Die Motoren gibt es mit sehr unterschiedlichen Drehzahlen, bitte beim Kaufen darauf achten. Der Motor sollte bei 6 Volt nicht mehr als 15 Umdrehungen pro Minute haben. Hinweis: bei dem Motor mit 1:1000 Übersetzung ist die Getriebebox 12mm lang, dieser Motor ist der Richtige. - Der Motor kann mit 4,5-6V betrieben werden. - Je nach Drucker Toleranz kann es notwendig werden die Löcher der Achsen und den Motor vorsichtig zu vergrößern oder einzukleben.
Statistics
Likes
50
Downloads
0