OmniStand Compatible Quick Connect Filament Spool Stands
Description
# Omnistand Compatible Quick Connect Filament Spool Stands ## Printer Compatibility * ***Flashforge Dreamer*** * ***Dremel 3D Idea Builder*** These Quick Connect Stands Are Compatible With The Omnistand Filament Spool Stand Set Found Here: Http://Www.Thingiverse.Com/Thing:652415 These Are The Original Stands Once Part Of The Omnistand Set. They Are Designed For Filament Weighing Up To 0.5 Kg. If Using Heavier Filament It'S Recommended To Use The Newer Stands Found In The Omnistand Set Which Are Designed To Handle Heavier Loads. ## Filament Spool Compatibility When Using A 100 Mm Filament Spool Rod (Found Here: Http://Www.Thingiverse.Com/Thing:652415), The Three Filament Rod Hole Positions Are Optimized For 3 Different Filament Spool Size Categories: Up To 184X65 Mm (7.24X2.55"), Up To 230X65Mm (9.05X2.55"), And Up To 190X77 Mm (7.48X3.03"). For Slightly Wider Spools See Here: Http://Www.Thingiverse.Com/Thing:667473 Using The 100 Mm Filament Spool Rod The Stand Was Tested To Fit The Following Filament Spools Inside The Flashforge Dreamer And Dremel 3D Idea Builder: * ***Asaptech Tpe*** (0.7 Kg White Tested) * ***Colorfabb*** (0.75 Kg Copperfill Tested) * ***Dremel*** (All Filament Tested) * ***Esun*** (0.5 Kg Bronze Tested) * ***Filamex*** (0.5 Kg Spools Of Abs/Pla Tested) * ***Flashforge Dreamer*** (All Filament Tested) * ***Hatchbox*** (1 Kg And 0.45 Kg Spools Of Abs/Pla Tested) * ***Magic Cube*** (0.45 Kg Abs Tested) * ***Mg Chemicals*** (0.25 Kg Of Pla/Abs Tested) * ***Ninjaflex*** (0.5 Kg Fire Color Tested) * ***Taulman*** (0.45 Kg Of T-Glase Tested) * ***Usafilament*** (0.5 Kg Pva Tested) * ***Zen Toolworks*** (1 Kg Wood Filament Tested, Others Might Not Fit) Filament Spools Tested That Cannot Fit Inside The Flashforge Dreamer Or Dremel 3D Idea Builder: * Filament Outlet (1 Kg Spool Of Hips Tested) * Gizmo Dorks (1 Kg Spool Of Hips Tested) * Shaxon (1 Kg Spool Of Abs Tested) * Usafilament (1 Kg Spool Tested) ## Filament Stand Base The Quick Connect Base For This Stand Is Part Of The Omnistand Set Found Here: Http://Www.Thingiverse.Com/Thing:652415 The Base Mounts Directly In Place Of The Flashforge Dreamer Or Dremel 3D Idea Builder'S Original Filament Stand. It Mounts To The Bottom Using The Original Filament Stand Holes And Screws. No Additional Hardware Is Needed. The Base Of The Stand Has A Unique Sturdy Quick Connect Design, Allowing Different Stands To Be Easily Exchanged Without Unscrewing Anything. This Allows Different Stand Designs To Be Inserted Into The Stand Base, Without The Need For Screws. ## Filament Stands Each Stand Has Three Rod Holes To Allow The Filament Rod To Better Accommodate Different Sized Filament Spools. The Bottom Rod Hole Is Specifically Designed To Fit Flashforge Dreamer And Dremel Filament Spools Allowing Them To Go Down Into The Filament Depression At The Bottom Of The Printer, Maximizing Clearance Space In The Printer. Other Filament Spools Up To 184X65 Mm Should Fit, But Some Spools Might Require An Additional Spacer For The Spool'S Hole. The Middle Rod Hole Is Designed For Filament Spools That Are Thin Enough To Fit Into The Filament Depression At The Bottom Of The Printer, But Too Large To Fit The Standard Flashforge Dreamer And Dremel Filament Stand. Spools Up To 230X65Mm Should Fit, But Some Rolls Might Require An Additional Spacer For The Spool'S Hole. The Top Rod Hole Is Designed For Filament Spools That Are Too Fat To Fit Into The Filament Depression At The Bottom Of The Printer. Spools Up To 190X77 Mm Should Fit (Or 190X82.5 Mm If Using The Maximum Length Rod Found Here: Http://Www.Thingiverse.Com/Thing:667473), But Some Spools Might Require An Additional Spacer For The Spool'S Hole. ## Filament Rod Spacers For Compatible Filament Rod Spacers See: Http://Www.Thingiverse.Com/Thing:652415 ## Filament Rods For Compatible Filament Rods See: Http://Www.Thingiverse.Com/Thing:652415 Http://Www.Thingiverse.Com/Thing:667473
Statistics
Likes
10
Downloads
0