Sapphire Plus, Mosquito hotend, Orbiter, belt tension, 4020 blower fans, space for ADXL345, and neopixel.
Description
Features: Twin 4020 blower fans BL touch holder space for ADXL345 behind 4020 fans Space for NEOPIXEL internal slots for cable routing 3d printed threads 8mm shorter than Stock Hotend, Maintains 300mm X and y stroke. Approx 340g fully assembled with Orbiter I run this at 150m/sec, 10K acceleration on Klipper for most prints, & it will go a lot faster if it is in a separate room. It will easily outrun a standard hotend, Magnum recommended, If you are going slow in PLA (less than 100mm/s), you may need to run fans at 50%, This is designed for my attempt to do a sub 8 min Benchy. #speedboatrace For V6 body look here : https://www.thingiverse.com/thing:4965868 Step files included for remixing, Most threads are 3d printed, if the thread form form is a bit off, put an m3 bolt in a drill and carefully run in in and out of the holes For Mounting, Din557 square nuts are recommend, but also accepts hex and heat stakes, Drill out the heat stake holes to the appropriate size for the heat stakes you have. if using mounting a Neopixel strip, do use a capacitor and resistor to protect the circuit. any LED strip may be mounted in the slot, BOM Belt Tension assembly 3d print Two "Tension belt" 3d print One "Tension Belt block" (or Hex nut varient) M3x 30 (2) (Belt tension) M3 x 20 (Mount to frame) DIN557 M3 (3) belt tension For Frame: 3d print "Frame" (Varies) choose one of Boden, Orbiter and Direct Drive, either with Logo and no logo, Direct Drive is intended to work with existing solutions to mount a BMG and/or a drag chain. M3 heat stake inserts (4) to mount orbiter and cable clamps, M2 x 8 mm (2) home switch M3x10 (4) Clamp Frame to MGN 12 Tension Block assembly For Body assembly: ADXL345 optional NEOPIXEL strip (2 or 3) optional. 3d print "Body" for Mosquito or V6 hotend Note Body 2 is lightened. 3d print Clampx for V6 M2.5x16 (2) to mount mosquito M3x30 (2) for mounting V6 DIN 557 (2) for V6 mounting) M3x6 (2) (Mount ADXL) DIN 557 M3 (or M3 hex) 4 or 6 4010 24v Axial fan M3x 16 (4) mount fan) Mount frame after Fans assembled M3x16 (2) (mount frame to body @ front) M3x20 (2) (mount frame to body @ back) For Fan assembly 3d print left and right Ducts Choose either Fan duct 1 or Fan duct 2, unsure which works best, several remixes exist too. 2x 4020 blower fans with front cover removed) M3x20 (6) to mount 4020 blower fans to frame Finishing touches: 2d print BL tough holder 3d print cable tidy Orbiter M3x10 (Mount orbiter) M2.5 x 8 Mount bl touch M2.5 heat stakes inserts (2) (optional bl touch) Bl touch or clone M3x16 (mount cable clamp to frame ) BL touch should be at x_offset: 20 y_offset: 22.25 z_offset: 1.7 Calibrate BL touch before use. Direct Drive has no additional mounting holes for cable management, as most direct drive mounts have it integrated, drill or use this trick to add holes if required https://www.youtube.com/watch?v=xc-6xVB9H4I
Statistics
Likes
33
Downloads
0