Ender 2 Pro - 210mm Printable Height - New Firmware Version
Description
This handle is used with the 2 spacers In and Under the Z-Axis Coupler. By raising the Z Lead Screw and Coupler you can, after changing the firmware, print to a height of 210mm. An increase of 30mm. (3cm) or (3/4") That increases the print height from almost 7 inches to almost 8 inches. The spacer with the hole goes under the Z Lead Screw Coupler. Fold a 1/4 sheet of paper 4 times and insert it between the spacer and the coupler. This keeps it from rubbing while you tighten the the screw for the motor shaft. The solid spacer goes in the 8mm end of the Coupler, and raises the lead screw up. Place it in the hole and then lower the lead screw into the hole and secure it with the coupler screw. By adding the 2 spacers, I was able to raise the printable height to 210mm. The handle has rounded edges so the cables and bowden tubing will slide around it. I have printed several 210mm vases, and they came out great. The NEW handle requires 2 M5x30mm button head screws to mount. I printed mine with a 0.6 nozzle at 100% infill. The spacers were printed with a 0.4 nozzle and also printed at 100% infill You can get the updated firmware at the following link: https://drive.google.com/file/d/1V6NXfTzKqB1hpwrNuiZyZh1WUPsL4cgN/view?usp=share_link This NEW Firmware has the following features and changes to it: 1. Updated Menu System to correct Menu Item Descriptions. 2. Cleaned up Main Information Screen. 3. Added "www.marlinfw.org" as the primary source file location. 4. Removed "www.creality.com and changed to "www.marlinfw.org" 5. Updated ALL applicable files to have correct updates. 6. Updated all applicable files from Creality v2.0.6.1 to Gorilla Tech v3.1.5 7. Changed Screen Time Out to 500000 ms to prevent screen from changing back to Main Information Screen to quickly. You will need to manually scroll back to previous screens. 8. Added LCD Assisted Four Corner Bed Leveling (Using Bed leveling Wheels and paper). 9. Added LCD Assisted Manual MESH Bed Leveling (Using Encoder knob to raise and lower nozzle at each of the 9 points around the bed using the paper method to build a Bed MESH. 9a. Limited MESH EDITING. 10. Removed Pre Heat for ABS Filament. 10a. Changed Pre-Heat Settings for PLA to the following: Hot-End 210c, Heated Bed 65c. Believe it or not, these are optimum settings. It has reduced my stringing, and I get better first layers. I also use a Spring Steel with PEI Sheet for my print bed. At over 60c this thing sticks like glue. You can always lower these default heat settings in the Advanced Settings , under PLA pre heat settings. 11. Enabled Long Print File Names. 12. Enabled Scrolling of Long Print File Names. 13. Added: Only For CPU Type: STM32F103RET6 Creality 4.2.3 Mainboards. 14. Added Filament Runout Sensor Capabilities (This can be turned off in advanced settings if you do not have a filament runout sensor) . 15. Removed Multi Language Function (English, Chinese). Default is now English. 16. Removed Language Option From Main Menu System. 17. Power Loss Recovery is OFF by Default . 18. Set up for Dual Gear Extruder with E-Steps of 143.5, if you do not have a dual gear extruder, you can reset the E-Steps to the OEM setting of 92.6 in the Advanced Settings Menu. 19. Addition of: Acceleration Editing. 20. Addition of: Velocity Editing. 21. Added Skew Compensation. This in case your bed is not quite straight side to side and front to back. If you have questions about this upgrade, feel free to message me. I only check Thingiverse every few days, so I may be slow to respond.
Statistics
Likes
0
Downloads
0