DIYLaserTable

Description

This project is maintained at https://github.com/hotwolf/DIYLaserBed. <a name="TOP"></a> # DIYLaserBed RevB This is a DIY laser bed for K40 cutters and clones.  --- <a name="DIYLB_top_assembly"></a> ## 2 x DIYLB Top Assembly ### Vitamins |Qty|Description| |---:|:----------| |4| Screw M6 cap x 20mm| |4| Washer M6 x 12.5mm x 1.5mm| ### 3D Printed parts | 2 x DIYLB_top_A.stl | 2 x DIYLB_top_B.stl | |---|---| |  |  ### Assembly instructions  1. Cut a M6 thread into the top of the vertical 20x20 extrusions 2. Attach the top holders 3. Secure the top holders with M6 screws  <span></span> [Top](#TOP) --- <a name="DIYLB_carriage_D_assembly"></a> ## DIYLB Carriage D Assembly ### Vitamins |Qty|Description| |---:|:----------| |5| Linear rail carriage MGN7C| |2| Nut M3 x 2.4mm | |4| Screw M2 cap x 10mm| |2| Screw M3 pan x 12mm| |1| Screw M4 cap x 12mm| |1| Screw M6 pan x 20mm| |1| T-Nut (20x20)| |1| T8-Nut (narrow)| |4| Washer M2 x 5mm x 0.3mm| |1| Washer M4 x 9mm x 0.8mm| |1| Washer M6 x 12.5mm x 1.5mm| ### 3D Printed parts | 1 x DIYLB_carriage_D.stl | |---| |  ### Assembly instructions  1. Attatch T8-nut to the carriage holder, using M3 screws, 2. Attatch the rail carriage to the carriage holder using M2 screws. 3. Put a T-nuts into the mounting hole.  <span></span> [Top](#TOP) --- <a name="DIYLB_carriage_C_assembly"></a> ## DIYLB Carriage C Assembly ### Vitamins |Qty|Description| |---:|:----------| |5| Linear rail carriage MGN7C| |2| Nut M3 x 2.4mm | |4| Screw M2 cap x 10mm| |2| Screw M3 pan x 12mm| |1| Screw M4 cap x 12mm| |1| Screw M6 pan x 20mm| |1| T-Nut (20x20)| |1| T8-Nut (narrow)| |4| Washer M2 x 5mm x 0.3mm| |1| Washer M4 x 9mm x 0.8mm| |1| Washer M6 x 12.5mm x 1.5mm| ### 3D Printed parts | 1 x DIYLB_carriage_C.stl | |---| |  ### Assembly instructions  1. Attatch T8-nut to the carriage holder, using M3 screws, 2. Attatch the rail carriage to the carriage holder using M2 screws. 3. Put a T-nuts into the mounting hole.  <span></span> [Top](#TOP) --- <a name="DIYLB_carriage_AB_assembly"></a> ## 2 x DIYLB Carriage AB Assembly ### Vitamins |Qty|Description| |---:|:----------| |2| Extrusion E2020 x 235mm| ### Sub-assemblies | 1 x DIYLB_carriage_A_assembly | 1 x DIYLB_carriage_B_assembly | 1 x DIYLB_carriage_C_assembly | |---|---|---| |  |  |  | 1 x DIYLB_carriage_D_assembly | |---| |  ### Assembly instructions  1. Cut a M6 thread into both ends of the extrusion, 2. Attatch attxh the carriage holders  <span></span> [Top](#TOP) --- <a name="DIYLB_carriage_B_assembly"></a> ## DIYLB Carriage B Assembly ### Vitamins |Qty|Description| |---:|:----------| |5| Linear rail carriage MGN7C| |2| Nut M3 x 2.4mm | |4| Screw M2 cap x 10mm| |2| Screw M3 pan x 12mm| |1| Screw M4 cap x 12mm| |1| Screw M6 pan x 20mm| |1| T-Nut (20x20)| |1| T8-Nut (narrow)| |4| Washer M2 x 5mm x 0.3mm| |1| Washer M4 x 9mm x 0.8mm| |1| Washer M6 x 12.5mm x 1.5mm| ### 3D Printed parts | 1 x DIYLB_carriage_B.stl | |---| |  ### Assembly instructions  1. Attatch T8-nut to the carriage holder, using M3 screws, 2. Attatch the rail carriage to the carriage holder using M2 screws. 3. Put a T-nuts into the mounting hole.  <span></span> [Top](#TOP) --- <a name="DIYLB_carriage_A_assembly"></a> ## DIYLB Carriage A Assembly ### Vitamins |Qty|Description| |---:|:----------| |5| Linear rail carriage MGN7C| |2| Nut M3 x 2.4mm | |4| Screw M2 cap x 10mm| |2| Screw M3 pan x 12mm| |1| Screw M4 cap x 12mm| |1| Screw M6 pan x 20mm| |1| T-Nut (20x20)| |1| T8-Nut (narrow)| |4| Washer M2 x 5mm x 0.3mm| |1| Washer M4 x 9mm x 0.8mm| |1| Washer M6 x 12.5mm x 1.5mm| ### 3D Printed parts | 1 x DIYLB_carriage_A.stl | |---| |  ### Assembly instructions  1. Attatch T8-nut to the carriage holder, using M3 screws, 2. Attatch the rail carriage to the carriage holder using M2 screws. 3. Put a T-nuts into the mounting hole.  <span></span> [Top](#TOP) --- <a name="DIYLB_rail_assembly"></a> ## 4 x DIYLB Rail Assembly ### Vitamins |Qty|Description| |---:|:----------| |4| Extrusion E2020 x 70mm| |4| Linear rail MGN7 x 70mm| |20| Nut M2 x 1.6mm | |20| Screw M2 cap x 6mm| ### 3D Printed parts | 4 x DIYLB_rail.stl | |---| |  ### Assembly instructions  1. Insert the M2 nuts into the printed holder. 2. Attach the rail loosely. 3. Slide the printed holder into the 20x20 extrusion and tighten the screws.  <span></span> [Top](#TOP) --- <a name="DIYLB_crank_assembly"></a> ## DIYLB Crank Assembly ### Vitamins |Qty|Description| |---:|:----------| |2| Ball bearing 608-2RS 8mm x 22mm x 7mm| |1| Extrusion E2040 x 60mm| |1| Extrusion E2040 x 70mm| |2| L-Bracket (20x20)| |1| Nut M8 x 6.5mm | |2| Pulley GT2 idler smooth 12mm| |1| Pulley GT2OB 20 teeth| |6| Screw M3 grub x 6mm| |2| Screw M4 cap x 15mm| |4| Screw M4 dome x 8mm| |3| Screw M8 hex x 50mm| |4| T-Nut (20x20)| |2| T-Nut (20x20)| |6| Washer M4 x 9mm x 0.8mm| ### 3D Printed parts | 1 x DIYLB_crank.stl | 2 x DIYLB_crank_bearing.stl | |---|---| |  |  ### Assembly instructions  1. Connect the two 20x40 extrusions with L-brackets. 2. Assemble the axis as illustrated. 3. Slide the printed holders over the vertical 20x40 extrusion (and loosely insert the timing belt). 4. Move the two printed holders as far apart as possible and tighten the screws. 5. Slide two idlers on T-nuts onto the top slot of the horizontal 20x40 extrusion.  <span></span> [Top](#TOP) --- <a name="DIYLB_lower_bearing_assembly"></a> ## 4 x DIYLB Lower Bearing Assembly ### Vitamins |Qty|Description| |---:|:----------| |4| Ball bearing 608-2RS 8mm x 22mm x 7mm| |4| Euro-Cent coin| |4| Pulley GT2OB 20 teeth| |8| Screw M3 grub x 6mm| |8| Screw M4 cap x 12mm| |8| T-Nut (20x20)| |4| Threaded rod M8 x 100mm| |8| Washer M4 x 9mm x 0.8mm| ### 3D Printed parts | 4 x DIYLB_lower_bearing.stl | |---| |  ### Assembly instructions  1. Put a EuroCent coin in the bottom of the lower ball bearing holder. 2. Squeze the ball bearing into the holder. 3. Attach two T-nuts with screws and washers. 4. Put the pulley loosely onto the threaded rod and insert them into the ball bearingpulles.  <span></span> [Top](#TOP) --- <a name="DIYLB_base_right_assembly"></a> ## DIYLB Base Right Assembly ### Vitamins |Qty|Description| |---:|:----------| |1| Extrusion E2020 x 300mm| |2| L-Bracket (20x20)| |4| Screw M3 grub x 6mm| ### Sub-assemblies | 2 x DIYLB_lower_bearing_assembly | |---| |  ### Assembly instructions  1. Slide two L-brackets onto the top slot of the 20x20 extrusion. 2. Slide the two holders for the ball bearings onto the lef-thand slot of the 20x20 extrusion.  <span></span> [Top](#TOP) --- <a name="DIYLB_magnet_cover_assembly"></a> ## 4 x DIYLB Magnet Cover Assembly ### Vitamins |Qty|Description| |---:|:----------| |4| Euro-Cent coin| ### 3D Printed parts | 4 x DIYLB_magnet_cover.stl | |---| |  ### Assembly instructions  1. insert cent coin during print.  <span></span> [Top](#TOP) --- <a name="DIYLB_magnet_assembly"></a> ## 4 x DIYLB Magnet Assembly ### Vitamins |Qty|Description| |---:|:----------| |4| Neodym Magnet (D=20,H=4.5)| |8| Screw M4 cap x 12mm| |8| T-Nut (20x20)| |8| Washer M4 x 9mm x 0.8mm| ### 3D Printed parts | 4 x DIYLB_magnet.stl | |---| |  ### Sub-assemblies | 4 x DIYLB_magnet_cover_assembly | |---| |  ### Assembly instructions  1. Squeze the magnet into the holder. 2. Attach two T-nuts with screws and washers. 3. Put the covers on top of the magnets.  <span></span> [Top](#TOP) --- <a name="DIYLB_base_center_assembly"></a> ## 2 x DIYLB Base Center Assembly ### Vitamins |Qty|Description| |---:|:----------| |2| Extrusion E2020 x 320mm| ### Sub-assemblies | 4 x DIYLB_magnet_assembly | |---| |  ### Assembly instructions  1. Attach two magnet holders to the 320mm 20x20 extrusion.  <span></span> [Top](#TOP) --- <a name="DIYLB_base_left_assembly"></a> ## DIYLB Base Left Assembly ### Vitamins |Qty|Description| |---:|:----------| |1| Extrusion E2020 x 300mm| |4| L-Bracket (20x20)| |8| Screw M3 grub x 6mm| ### Sub-assemblies | 2 x DIYLB_lower_bearing_assembly | |---| |  ### Assembly instructions  1. Slide two L-brackets onto the top slot of the 20x20 extrusion. 2. Slide the two holders for the ball bearings onto the right-hand slot of the 20x20 extrusion. 3. Slide two L-brackets onto the left-hand slot of the 20x20 extrusion.  <span></span> [Top](#TOP) --- <a name="DIYLB_Base_assembly"></a> ## DIYLB Base Assembly ### Sub-assemblies | 2 x DIYLB_base_center_assembly | 1 x DIYLB_base_left_assembly | 1 x DIYLB_base_right_assembly | |---|---|---| |  |  |  ### Assembly instructions  1. Attach all parts of the base frame 2. Tighten the screws of the bearing holders, connecting 20x20 extrusions  <span></span> [Top](#TOP) --- <a name="DIYLB_crank_to_base_assembly"></a> ## DIYLB Crank To Base Assembly ### Sub-assemblies | 1 x DIYLB_Base_assembly | 1 x DIYLB_crank_assembly | |---|---| |  |  ### Assembly instructions  1. Attach the crank holder to the base of the frame 2. Tighten the screws of the L-brackets  <span></span> [Top](#TOP) --- <a name="DIYLB_columns_to_base_assembly"></a> ## DIYLB Columns To Base Assembly ### Sub-assemblies | 1 x DIYLB_crank_to_base_assembly | 4 x DIYLB_rail_assembly | |---|---| |  |  ### Assembly instructions  1. Attach the for columns to the base of the frame 2. Tighten the screws of the L-brackets  <span></span> [Top](#TOP) --- <a name="DIYLB_bed_to_columns_assembly"></a> ## DIYLB Bed To Columns Assembly ### Sub-assemblies | 2 x DIYLB_carriage_AB_assembly | 1 x DIYLB_columns_to_base_assembly | |---|---| |  |  ### Assembly instructions  1. Thread the assembled carriage holders into the rails and rods of the Z-axis.  <span></span> [Top](#TOP) --- <a name="DIYLB_beams_to_bed_assembly"></a> ## DIYLB Beams To Bed Assembly ### Vitamins |Qty|Description| |---:|:----------| |1| Flat section 15mmx2mm, 272mm| |4| Flat section 15mmx2mm, 316mm| ### 3D Printed parts | 8 x DIYLB_beam_holder.stl | |---| |  ### Sub-assemblies | 1 x DIYLB_bed_to_columns_assembly | |---| |  ### Assembly instructions  1. Attach the beam holders to the horizontal 20x20 extrusions of the bed. 2. Slide the beams into the beam holders  <span></span> [Top](#TOP) --- <a name="DIYLB_top_to_columns_assembly"></a> ## DIYLB Top To Columns Assembly ### Sub-assemblies | 1 x DIYLB_beams_to_bed_assembly | 2 x DIYLB_top_assembly | |---|---| |  |  ### Assembly instructions  1. Attach the top extrusions to the rest of the frame.  <span></span> [Top](#TOP) --- <a name="DIYLB_belt_assembly"></a> ## DIYLB Belt Assembly ### Vitamins |Qty|Description| |---:|:----------| |1| Belt GT2 x 6mm x 1212mm| ### Sub-assemblies | 1 x DIYLB_top_to_columns_assembly | |---| |  ### Assembly instructions  1. Insert the timing belt 2. Level the bed by turning the thraded rods, before tightening the pulleys  <span></span> [Top](#TOP) --- Finished! <span></span> [Top](#TOP)

Statistics

Category

Tags