Zeb'210 FPV Racer Quadcopter
Description
Zeb'210 Fpv Racer Quadcopter - Custom Frame. Presentation: * Inspired By Sigan'S Quadcopters Design, But Whole New Design. * Designed For The List Of Parts Here Below. * All Electronic Parts Are Attached On The Body (Spacer) Of The Frame With Specific Mounts ; Some Adjustments Might Be Necessary If You Want To Use Different Electronic Parts. * The Body And The Two Holders Are Intended To Be Printed In Sls Nylon. * The Three Plates Are Intended To Be Cut From Cfrp (3K Carbon Fiber Sheet) 1.5Mm Thick Sheets. Specifications: * External Dimensions Are 217.5 X175.5 X46.5Mm, With 213.3Mm Motor To Motor, For 5" Propellers. * The Body Is 15Mm High (12Mm Inside Space), And Its External Wall Is 3Mm Thick. * The Motors Guards Are 4Mm Thick, The Motors Mounts Are Tilted 12° Forward And Are 4Mm Thick. * The Fpv Camera Is Tilted 13° Upward, And The Camera Lens Guard Is 2.5Mm Thick. * The Rx Antennas Are Tilted 25° On Each Sides Of The Camera Lens Guard, Which Leaves 35Mm Clearance Across The Width For An External Camera (Mobius For Instance) On The Top. * Accept Battery Up To 108Mm Long And 37Mm Wide, With Suitable Battery Holder. * The Battery Holder Is Fixed On The Middle Plate Using Five Oblong Lugs. * The Mobius Holder Is Fixed On Top Of The Top Plate, It Protects The Lens With A 2.5Mm Guard. * Vtx Channel Setting Is Reachable From Underneath With The Frame Closed. * Usb Ports From Fc And Osd Are Both Reachable From The Left Side With The Frame Closed. * Fc'S Alarm Buzzer Mount Leads The Sound Directly Outside From The Right Side. * Three Serial Leds Controlled By The Fc Are Integrated In Each Arm For Higher Visibility. Part List: * *Flight Controller:* [Rmrc Seriously Dodo Rev3](Http://Goo.Gl/4K2Azd) * *Pdb/Osd:* [Mxk Pdb With 5V And 12V Converter, Lc Filter, And Minimosd Integrated](Http://Goo.Gl/Wkaesv) * *Escs:* [Fvt Littlebee 30A](Http://Goo.Gl/2Zanms) * *Motors:* [Emax Rs2205 2300Kv](Http://Goo.Gl/Dvqaqv) * *Props:* [Hqprop 5045 Bullnose](Http://Goo.Gl/Mhrhvc), [Hqprop 5040 Tri-Blades](Http://Goo.Gl/Tav76R) And [Hqprop 5045 Bullnose Tri-Blades](Http://Goo.Gl/Izjidv) * *Camera:* [Runcam Pz0420M](Http://Goo.Gl/Hz447Z) With [2.1Mm Lens](Http://Goo.Gl/S8Ry7C) * *Action Camera:* [Mobius Wide Angle C2](Http://Goo.Gl/H12Eky) With [32Gb Microsd Card](Http://Goo.Gl/Cztkms) * *Video Tx:* [Eachine Et600](Http://Goo.Gl/73Qkzm) With [Rp-Sma Adapter](Http://Goo.Gl/Yofoww) And [Fatshark Spironet](Http://Goo.Gl/Gug2Un) * *Remote Rx:* [Lemon Rx Ppm-8 Diversity Lm0039](Http://Goo.Gl/8Kywts) With [Antenna Mounts](Http://Goo.Gl/Bjp2Hi) * *Lipo:* A Few [Dronelabs 4S 1800Mah 50~100C](Http://Goo.Gl/C9Qt8A) * *Other:* [Leds Ws2812 Bandstripes](Http://Goo.Gl/K6Wqmv), [Battery Strap](Http://Goo.Gl/Sf62M2), [Battery Pad](Http://Goo.Gl/5Cfkul), [5V Buzzer](Http://Goo.Gl/3Ioezw), [Xt60 Connector](Http://Goo.Gl/Uggb0M), Etc. Needed Hardware: * [1.5X450X200Mm Carbon Fiber Sheet](Http://Goo.Gl/Ot2Wff) * 8X [Hex Threaded Standoff M3X12Mm](Http://Goo.Gl/Oz3Tmk) * 4X [Round Threaded Standoff M3X20Mm](Http://Goo.Gl/G7Fqae) * 24X [Screw M3X6Mm](Http://Goo.Gl/Idr4Hh) (For All Standoffs) * 8X [Screw + Nut M3X6Mm Nylon](Http://Goo.Gl/Bwyceu) (For Fc And Pdb/Osd) * 6X [Screw + Nut M2X6Mm Nylon](Http://Goo.Gl/7Qvgoz) (For Fpv Camera And Xt60) * [Small Zip Tie](Http://Goo.Gl/Tcsg6G) (For Escs And Vtx) * Double-Sided Adhesive (For Rx And Leds) Ground Base: * *Goggles:* [Quanum Fpv Goggle V2](Http://Goo.Gl/T58D0R) * *Video Rx:* [Eachine Rc832](Http://Goo.Gl/Zlzxzp) * *Remote Tx:* [Walkera Devo 10](Http://Goo.Gl/Fvxfua) With Deviationtx Firmware * *Lipo:* [Turnigy 3S 2650Mah 1C](Http://Goo.Gl/Izfybj) * *Charger:* [Skyrc Imax B6Ac V2](Http://Goo.Gl/3Hzlfx) 3D Parts Are Available On Shapeways For Sls Printing: * [Body (Spacer)](Http://Shpws.Me/Ljyq) * [Mobius Holder](Http://Shpws.Me/M2Ym) * [Battery Holder](Http://Shpws.Me/Ljys) 3D Tools View Of Each Parts: * [Body (Spacer)](Https://Goo.Gl/Bydijb) * [Mobius Holder](Https://Goo.Gl/2Dvll3) * [Battery Holder](Https://Goo.Gl/Ykbdv5) * [Bottom Plate](Https://Goo.Gl/Ov0Bhl) * [Middle Plate](Https://Goo.Gl/Nmwvka) * [Top Plate](Https://Goo.Gl/Jkgykx) Talk About It On: * [Rcgroups](Http://Www.Rcgroups.Com/Forums/Showthread.Php?T=2615370) * [Multi Rotor Fan Club (French)](Http://Multi-Rotor-Fans-Club.Com/Viewtopic.Php?F=30&T=16937) Remarks: * *Solidworks Files Are Included For Customization.* * *See My Prototype In The Made Section For More Information.*
Statistics
Likes
281
Downloads
0