Openbuilds v-slot X axis for Lulzbot TAZ 6 printers With integrated Z anti Wobble
Description
This Is The Taz 6 Specific Variant Of The Openbuilds X Axis Rail Modification, Anti-Wobble Edition. For The Non Antiwobble Edition, Please Try Here: Https://Www.Thingiverse.Com/Thing:2692604 Instructions Are Still Being Worked On. It'S Basically Identical To The Taz 5 Version, But With Anti Wobble Pins And Bearings And A Few Extra M5 M3 And M2 Bolts And Heat Set Inserts. Bill Of Materials: Anti Wobble: 3/16" Rods: 8X 32Mm 16X Igus Myi-03-03 Flanged Bearing, 3/16 Idx3/16 In L Bearings (5 Per Pack - 4 Packs, 2 Spare Bearings) 8 M5 Heat Set Inserts X Motor End 4X M2 Heat Set Inserts 2 20Mm M5 Cap Head Bolt 1 12Mm M5 Cap Head Bolt 2 M5 T Slot Nut X Idler End 2 20Mm M5 Cap Head Bolt 1 12Mm M5 Cap Head Bolt 2 M5 T Slot Nut 2X M3 Heat Set Inserts 2X 10-12Mm M3 Cap Head Bolt X Motor Mount 4X 10Mm M5 6X M5 11Mm Long Heat Set Inserts (Mcmaster Carr ) 4X M5 T Slot Nuts X Motor Mount Plate 10Mm M5 Bolts 6X 12Mm M3 4X Bolts X Idler Mount Stock Lulzbot Idler Bearings, Washers, Nut And 8Mm Bolt 2 6.75Mm Long M5 Heat Set Inserts 2 M5 32Mm Bolts (The Idler Adjusters 2 10Mm M5 Bolts 2 M5 Tslot Nuts X Carriage Adaptor Plate 4X M3 8Mm Bolts 11 M3 Heat Set Inserts (The Short 3Mm-4Mm Ones) Stock Lulzbot V Notch Plastic Piece. Stock 4 Bolts And Washers That Hold Down That Piece (M3 10Mm Thread Plus M3 Washers) The Stock Lulzbot Carriage Hold Down Bolt And Washer (M3 Washer M3 Bolt 10Mm Thread) Backplate 1 35Mm Long M5 Low Profile Bolt (I Use The Openbuilds Ones) And 1 35Mm Long M6 Bolt (Or ¼” Bolt) Printable Spacers 2X 1/8" Bolt, 1 Inch Or So Long 4X 1/8" Nuts 4X Large-Ish Washers Bigger Than The Plastic Spacers To Keep The Bolt Slipping Off The End You Will Need Much Longer Bolts If You Are Attempting To Use The Printed Backplate. I Still Have Metal Backplates Available. Openrails Parts: 1 60Mm X 20Mm Openbuilds Linear Extrusion 500Mm Long Extrusion, Manually Remove 40Mm. Http://Openbuildspartstore.Com/Black-V-Slot-Linear-Rail/ 4 Sets Of Bearing Wheels (Http://Openbuildspartstore.Com/Xtreme-Solid-V-Wheel-Kit/ Or Other Sets) , 4 Spacers (6Mm ) Http://Openbuildspartstore.Com/Aluminum-Spacers/ 2 Eccentric Spacers Also 6Mm Http://Openbuildspartstore.Com/Eccentric-Spacer/ One Of Their Gantry Mounting Plates. Http://Openbuildspartstore.Com/V-Slot-Gantry-Plates/ Flat Head M5 Bolts And Nuts 30Mm (Standard Bolts Will Not Fit, Need The Flat Ones. ). Longer If You Plan To Add The Cable Chain Pieces The Non Antiwobble Variant Is The Same, You Just Eliminate The Wobble Parts And Add 2 More M5 Heat Set Inserts Per X Endcap. The Completed Installation Picture Is Provided Courtesy Kam Vedbrat And Is Used With Permission, All Rights For The Photo Remain With Him. Thank You Kam!
Statistics
Likes
35
Downloads
0