Anet A8 E3D V6 Bowden Dual Extruder Mount Pruisa i3 Clone X Carriage
Description
#Please See The Newer Version [Here](Https://Www.Thingiverse.Com/Thing:2766701) It Features A Much Better Design With More Compatibility And Better Cooling! Updated 1-18-18 Ready To Go! See It Run Here: Https://Youtu.Be/Nrn9100Mqby See My Rear Sensor Mount Version Here Https://Www.Thingiverse.Com/Thing:2763157 All Instructions Are For The Anet A8. Reduced Some Sizes, Moved Some Things And Cleaned It Up. I Added Some Zip Tie Holes In The Sides And Improved Tolerances. I Made Slotted Holes Because My Printed X Mounts Changed The Dimensions A Bit. I Have Printed, Installed And Now Used This Part. Below Are Instructions On How To Set It Up. I Printed Them With 1.8Mm Wall And 30% Fill. I Also Made A Set At 1.2Mm Wall And 15% Fill That Worked Perfectly. Both In Pla. This Includes Guides Like My Thing Https://Www.Thingiverse.Com/Thing:2732685 Built Into The Mount. Get The Latest Skynet3D Firmware From Https://Github.Com/Thijsk/Skynet3D And Please Update Your Firmware As Follows: Enable Ramps Boards, This Is For The Common Ones Like Https://Goo.Gl/Xw91Zh [Amazon.Com Link] Please Pay Attention And Be Sure To Choose The Correct Code For Your Motherboards. See Boards.H In The Skynet Firmware For A List. Define Motherboard Board_Ramps_14_Eeb Enable Dual Extruders: Define Extruders 2 Offsets For The Extruders: Define Hotend_Offset_X {0.0, 35.00} Define Hotend_Offset_Y {0.0, 0.00} For The Probe It'S : Define X_Probe_Offset_From_Extruder -35 // X Offset: -Left +Right [Of The Nozzle] Define Y_Probe_Offset_From_Extruder 4 // Y Offset: -Front +Behind [The Nozzle] Define Z_Probe_Offset_From_Extruder -0.5 // Z Offset: -Below +Above [The Nozzle Set This To Your Machine. I Used A .5Mm Thick Print Put Between The Bed And Probe With The Nozzle Touching The Bed To Start.] You Also Need To Set Travel Limits: // Travel Limits After Homing (Units Are In Mm) Define X_Max_Pos 240 Define X_Min_Pos -15 Define Y_Max_Pos 230 Define Y_Min_Pos -13 Define Z_Max_Pos 230 Define Z_Min_Pos 0 And Probe Point Offsets: // Set The Boundaries For Probing (Where The Probe Can Reach). Define Left_Probe_Bed_Position 27 Define Right_Probe_Bed_Position 200 Define Back_Probe_Bed_Position 200 Define Front_Probe_Bed_Position 20 See Https://Goo.Gl/Nkkgsb [3D Print Wiki] For The Best Instructions I Have Found So Far On How To Set Your Probe Z Offset. I Did This Using The Terminal In Octoprint Via To Raspberry Pi On The Printer. I Am Running Ramps 1.4 With Skynet Firmware. Anyways, This Is Getting Out Of Hand So Here'S The Important Stuff: Many Models To Choose From! - No Sensor Mount - 18Mm Sensor - 12Mm Sensor - 8Mm Sensor Then Choose You Cap: - 2 Stock Fans With Chain Mount - 2 Stock Fans No Chain Mount - No Fans No Chain Mount - No Fans With Chain Mount - If You Need Them There'S Fan Spacers Too. I Found My Duct Hit The Extruder. If You Go With One With A Chain Mount I Have Included The X Axis Chain Links From Https://Www.Thingiverse.Com/Thing:2193695 This Is What I Remixed From. You May Get The Other End Mount From Here Or Use Mine At Https://Www.Thingiverse.Com/Thing:2762145 Then Choose You Print Settings: - Choose .Amf Or .Stl. I Found .Amf More Accurate And Works In Cura. - Made One At .4Mm Nozzle, .2Mm Step, 1.6Mm Wall And 30% Fill Worked Great - Made A Second At .4Mm Nozzle, .2Mm Step, 1.2Mm Wall And 15% Fill, Worked Just As Good. - Do Your Own Of Course! You Guys Know What'S What. You Will Need: 1) E3D Style Extruders 2) Ramps 1.4 Or 1.5 3) Marlin/Skynet Firmware 4) 40Mm M4 Screws And Nuts For The Cap, 3 Of Them 5) 50Mm Blower Fan 6) Wires, Connectors, Crimpers, And A Soldering Iron Helps. I Have Made A Guide In Pdf Form Available Here Https://Goo.Gl/1S8Jsr For Setting The Offsets. You Will Need A Serial Connection To Your Printer And I Found Using Octoprint Is Really Easy. Here'S A Crapcad Schematic Of The Optocoupler Board I Made To Run The 12V Probe Completely Isolated From The Ramps Board.  Thank You! Enjoy And Please Like, Comment And Share!
Statistics
Likes
63
Downloads
0