Complete High End Wanhao I3 / Maker Select Corexy Rebuild (WIP)

Description

<H2>Work In Progress: Many Parts Still Need To Be Tested, Designed, And Uploaded</H2> <H2>Wanhao I3 / Maker Select Corexy Rebuild</H2> <H4><Strong>Warning: This Rebuild Is Not Simple And Cheap, And Will Take A Lot Of Time. Read Through <I>Everything</I> Below Before Deciding And Purchasing Parts</Strong></H4> <Hr> <H3>Pros Of This Rebuild</H3> - Rigidity: Frame Made Completely Of Aluminum Extrusions- Much Stronger Than The Stock Metal Sheet Frame - Precision: Mgn12 Rails Are Much Stiffer, And Offer Much More Stability. Ball Screws On Z-Axis Allow For More Precise Bed Movements - Faster Prints: By Only Allowing The Heavy Bed To Move In Z, And Extruder In X And Y, Print Speed Is Greatly Improved And Ringing Is Largely Reduced. Acceleration And Jerk Can Therefore Be Increased. Higher Torque Motors Will Allow For Faster Prints As Well. - Fits In A Typical Lack Enclosure - Larger Print Volume: Not Certain On Exact Size Yet- ~330X330X240 - Easily Modified- X Y And Z Are Easily Increased, <H3>Cons Of This Rebuild</H3> - Expensive: Total Cost Is Around ~$300. - Many Stock Parts Are Unused: X, Z, Rods & Leadscrews, Bed, Entire Frame Are Unused. This Is In Order To Turn This Printer Into A High-Grade Printer, So Cheap Stock Parts Were Generally Avoided And Replaced. - Not Easily To Assembly: A Lot Of Brackets, Screws, And Parts - Stock Board Is Most Likely Unable To Run Corexy Kinematics: I'M Running A 32 Bit Mks Board. <Hr> <H3>Bom<Br>* Means The Part Is From Stock Printer</H3> Will Be Adding Links Later <H4>Aluminum Extrusions(From Misumi)</H4> <H5> 2020</H5> - 6 X 30Mm - 2 X 60Mm - 2 X 350Mm - 2 X 351Mm - 4 X 400Mm - 6 X 423Mm - 2 X 463Mm <H5> 2040</H5> - 2 X 60Mm <H4>Rods</H4> <H5> 8Mm Rods</H5> - 2 X 380Mm <Strong>*</Strong> <H5> 12Mm Rods</H5> - 1 X 400Mm <H5> Rod Clamps</H5> - 4 X Sk8 - 2 X Igus Was-12 <H4>Bearings</H4> - 1 X Lm8Luu <Strong>*</Strong> - 1 X Igus Rjzm-08 <Strong>Must Be Metal</Strong> - 1 X Igus Rjum-12 <Strong>Must Also Be Metal</Strong> <H4>Ball Screws & Clamp</H4> - 2 X 350Mm 1605 Ballscrew + Nut (Mine Were Cut From 550Mm) - 2 X Igus Kstm-16 <H4>Flexible/Spider Coupling</H4> - 2 X 5*10 Flexible Coupling <H4>Linear Rails</H4> - 3 X 400Mm Mgn12 <H4>Bed</H4> <H5> Aluminum Plate</H5> - 1 X 1/4 Inch Mic 6/Tooling Aluminum Plate (Dimensions Tbd) <H5> Silicone Heater</H5> - 300X300 24V Silicone Heater W/ Adhesive <H4>Nema 17 Motors</H4> <H5> Z-Axis Motors</H5> - 2 X 48Mm Nema 17 <Strong>*</Strong> <H5> Top Motors</H5> - 2 X 48Mm Nema 17(Recommended) <Strong>Or</Strong> Stock X&Y Motors <Strong>*</Strong> <H4>Idlers/Belts</H4> <H5> Toothed Idler</H5> - 2 X Gt2 20 Teeth Timing Pulley <Strong>*</Strong> <H5> Smooth Idler</H5> - 8 X Gt2 Smooth Idler <H5> Belts</H5> - 5 Meters Fystec Fiberglass Reinforced Belts (Cheap And Are Decent Quality Belts) <H4>Brackets</H4> <H5> Top Motor Bracket</H5> - 2 X Aluminum 2020 Nema 17 Bracket <H5> Corner Brackets</H5> - 18 X 90 Degree Aluminum Bracket - Around 25 X 90 Degree Corner Bracket - 8 X 2040 90 Degree Corner Bracket <H4>Screws: Highly Recommend Purchasing From Trimcraftaviationrc</H4> - Around 200 X M5 * 10Mm

Statistics

Category

Tags