Duet WiFi Case Assembly | CR-10S 3D Printer
Description
This Has Been A Long Work In Progress But I Have Finally Finished The First Working Prototype For My Duet Wifi Case. The Intent Behind This Specific Design Was To Be Able To Enclose The Various Electronic Components That Are Utilized In My Highly Modified Cr-10S. I Was Able To Wire And Contain Everything In An Organized Way By Using A Combination Of Flex Guard Convoluted Tubes And Zip Ties. **Fyi: This Build Requires Almost A Full Kg Of Filament Depending On Slicer Settings. So Be Sure To Have A Full Roll Of Filament Ready And Make Sure Your Printer Is Dialed In Before Attempting To Print These Large Components.** This Case Is Designed To Contain The Following Components: **1X Duet Wifi Control Board** Https://Www.Filastruder.Com/Collections/Electronics/Products/Duet-Wifi **1X Solid State Relay** Https://Www.Amazon.Com/Gp/Product/B0087Ztn08/Ref=Oh_Aui_Detailpage_O01_S00?Ie=Utf8&Psc=1 **1X Heater Mosfet** Https://Www.Amazon.Com/Gp/Product/B01Mu3H01A/Ref=Oh_Aui_Detailpage_O03_S00?Ie=Utf8&Psc=1 **2X Power Switches** Https://Www.Amazon.Com/Gp/Product/B00Nwo68Ji/Ref=Oh_Aui_Detailpage_O06_S00?Ie=Utf8&Psc=1 **1X Power Supply** Https://Www.Amazon.Com/Gp/Product/B00If93H6W/Ref=Oh_Aui_Detailpage_O08_S00?Ie=Utf8&Psc=1 **2X 40Mm Case Fans** Https://Www.Amazon.Com/Gp/Product/B009Nqlt0M/Ref=Oh_Aui_Detailpage_O04_S00?Ie=Utf8&Psc=1 **1X 50Mm Case Fan** Https://Www.Amazon.Com/Noiseblocker-Nb-Blacksilent-Ultra-Silent-3000Rpm/Dp/B0083A0Cbg/Ref=Sr_1_1?S=Electronics&Ie=Utf8&Qid=1526523975&Sr=1-1&Keywords=Noiseblocker+Fan I Have Personally Made My Own Board To Handle The 24V To 12V Step Down For Case Fans And The Inductive Sensor Using The Following Transistors(Https://Www.Amazon.Com/Gp/Product/B076R44Fs7/Ref=Oh_Aui_Detailpage_O02_S00?Ie=Utf8&Psc=1). The Type Of Pcb I Soldered These Too Is Here: Https://Www.Amazon.Com/Gp/Product/B01M7R5Yib/Ref=Oh_Aui_Detailpage_O08_S00?Ie=Utf8&Psc=1 Hardware Needed For Assembly Of Components May Vary Depending If You Purchase The Earlier Mentioned Electronics Or Not, But I Used The Following Below: **Duet Wifi Board** --> 4X M4X0.7, 6Mm Lg Screws With 4X Plastic Washers **Ssr** --> 2X M5X0.8, 5Mm Lg Screws **Case Fans** --> 6X M4X0.7, 14Mm Lg Screws **Power Switches** --> 4X M4X0.7, 6Mm Lg Screws **Heater Mosfet** --> 4X M3X0.5, 5Mm Lg Screws The Duet Wifi Case And Psu Case Are Designed To Be Mounted Onto The Cr10 Frame With Screws And T-Slot Nuts So That The Unit Can Be Moved Without Carrying The Components Individually. However, It Is Still Advised To Be Cautious When Moving The Assembly As An Adequate Amount Of Weight Will Be Cantilevered Off The Edge Of The Frame. **Disclaimer**: I Claim No Responsibility For Any Damage That May Result From Assembly And Wiring Of Electronics Incorrectly, Or Drops Resulting From Inadequate Mechanical Fastening. **3D Cad Design Credit** Duet Wifi_Phil Maddox - Grabcad Dc Power Supply_Luca - Grabcad Urbest Power Switch_Richard Bruning - Grabcad Uxcell Ssr_Xinchao Song - Grabcad Flexible Motor Coupling_Eoghan O'Duffy - Grabcad Noctua 40Mm Fan_Sean - Grabcad
Statistics
Likes
29
Downloads
0