Purpose

This project is in response to the mountain of parts I keep collecting. So much so, that I’ve now filled four different categories of parts, I have now created a carousel, that will hold all of these, allowing a stepper motor to turn a platter, on which the containers sit..

------------------------------------------------------------------------------------------------------------------------ Main Components: **The major components that make this project work are;** 1/ An Arduino Mega 2560 (you could also use a due, which would run faster) 2/ A 3.95 inch (RED) touch screen display 3/ A4988 Stepper Driver 4/ My board design for Power Supply & relay 5/ 608zz bearings (skateboard wheels) for the carousel to rest on 6/ Springs to allow the carousel to maintain a level base for containers 7/ A stepper motor Nema17 x 39mm (approx 1.5 Amp per phase) I used 17HS15-1504S-X1 Nema 17 Stepper Motor 45Ncm 8/ NJC5002c Hall-Effect (magnet) sensor ---------------------------------------------------------------------------------------------------------------------- This is my fifteenth __'Thing'__, & also my fifteenth __'Fusion 360'__ design. My other projects Wire bobbin: https://www.thingiverse.com/thing:4946929 Flux Funnel: https://www.thingiverse.com/thing:4946257 Large Spool holder: https://www.thingiverse.com/thing:4816080 TUSH with Linear Bearings: https://www.thingiverse.com/thing:4815574 T-962 Modification: https://www.thingiverse.com/thing:4760915 Desiccant funnel: https://www.thingiverse.com/thing:4716424 Case for 3.5" VGA Display: https://www.thingiverse.com/thing:4291794 Sandpaper Holder with magnets: https://www.thingiverse.com/thing:4213700 Gear Driven TUSH: https://www.thingiverse.com/thing:4196767 Tight fitting Container & Lids: https://www.thingiverse.com/thing:4158760 Ride RD6006 Case: https://www.thingiverse.com/thing:4073804 Micro Pump Holders: https://www.thingiverse.com/thing:5164094 Containers for Carousel https://www.thingiverse.com/thing:5199867 Dremel Jigs for circles https://www.thingiverse.com/thing:5267056 ------------------------------------------------

Parts List:

------------------- 3D Printed Parts: 1. 8 x bearing Caps 2. 8 x Outer Bearing Holder 3. Central Motor Holder 4. Electronics Bay Base (with holders for Power Supply & Arduino Mega) 5. Electronics Bay Cover (either for Large or Small Sensor) 6. Inner Shell 7. Keyed protusion 8. Mid cover (either for Large or Small Sensor) 9. Pen Enclosure (with it's assorted parts as one .stl file) 10. Top Platter (complete) 11. Keyed Protrusion (to connect stepper shaft tp Platter) 12. Spring gapping tool (to ensure all springs on Platter are set the same) Hardware: 1. 17HS15-1504S-X1 39mm Stepper Motor 2. Top Platter Springs 8 of .7mm x 5mm x 20mm 3. 8 of 608zz Bearings 4. 8 of M3 x 6mm Bolt 5. 8 of M3 x 25mm Bolt 6. 8 of M3 x 20mm Bolt(to join both bases together) 7. 8 of M3 Nuts (for bolts above) ***Pen Ensclosure:*** 1. M3 x 8 Grub Screw 2. 5mm x 17mm Compression Spring 3. 5mm x 12mm Extended Spring 4. 5 of M2 x 10mm Bolt 5. M2 x 25mm Bolt 6. M3 x 10mm Bolt 7. M3 Hexagonal Nut -----------------------------------

Found 2 3D-models for “Hall-Effect Sensor” across many websites

Rotating Carousel for Parts Containers

CH Pro Pedals - Brake Potentiometer Replacement (Hall-Effect Sensor)